Skip to main content
#
 
site map
contact
Shipping Policies
HOME
Board Shorts Main
SPF Performance Shirts
Side To Shorts & Shirts
4X4 Board Shorts
Board Shorts
SURF Board Shorts
Side To Shirts
Men's SPF Performance Shirts
Men's Short Sleeve SPF
Ladies' Board Shorts
Ladies' Printed SPF 50 Tops
Ladies' SPF Shirt/Rash Guards
Ladies Sport T's & Skorts
Youth Apparel
Face Shields
Head Gear
Apparel Catalog
Ladies Board Shorts Measurements
Marlin Camo Performance Shirts
Reef Break Boardshorts
Reef Break II
Shirt, Hat, NUFF Combos
T Shirts
Ladies' Bermuda Collection
Apparel
Offshore Trolling Plastics
Chrome Head Trolling Lures
Daisy Chains & Multi Bait Rigs
Replacement Skirts
Soft Trolling Lures
Looney Birds
Dredge Baits
Ballyhoo Covers
Vertical Jigs, Inshore Jigs, Spoons
Lure Kits & Rigs
Hooks & Rigs
Dredge Witch
Spreader Bars Main
Slap Happy
Replacement Jigging Hooks
Tackle
Surfboards
Surf Leashes
Surf
Rigging a Goggle Eye Harness
Yellowfin Tuna Fishing
Trolling for Grouper
Fishing tips for Wahoo
Live Bait Fishing - Surface
Daytime Swordfishing
Fishing for Dolphin
Making Concrete Weights for Swordfishing
Which Lure Colors?
Trolling without Outriggers
Catching a Spiny Lobster
Jigging for Kingfish
Daisy Chains and How They Work
Which Lure?
Trolling Diagrams
Rigging Ballyhoo
Rigging
About
Salmon Nigiri Plate
Salmon Rice Bowl
Venison Bar-b-que
The Ultimate Nacho
Lemon Mangrove Snapper
Real Bahamian Conch Chowder
Grilled Cajun Spice Dolphin
Italian Seasoned Grilled Yellowfin Tuna
Grilled Florida Lobster Tails
Grilled Kingfish Sandwich
How to prepare a Wahoo Fillet
Fantastic Fish Recipes
Contact
Testimonials

How to rig a Ballyhoo without a pin....

As you may have read, I no longer troll Ballyhoo as I wish to prove our lures consistently and I also save room in my freezer for fish. But, I do still advocate the use of Ballyhoo because after you have hooked a Mahi on one of our lures, if you have a Ballyhoo left out there dangling from an outrigger while you are fighting your Mahi, you have a shot at getting hit by another Mahi. With our lure hanging in a rigger, that chance diminishes quite a bit, so if you want to rig a Ballyhoo behind one of our rigged lures or without a wire leader and without a pin for the chin, read below....

  1. Tie (wrap) your copper wire to the loop of the mono that holds the hook.
  2. Measure hook next to Ballyhoo with the copper wire (where wrapped to mono) is next to the nose of the Ballyhoo (where the pin usually goes through)
  3. See where the hook should exit the Ballyhoo’s underside and take hook point and mark the spot by making a small hole
  4. Pass hook through Ballyhoo’s gill as usual
  5. Exit hook through small hole you made in underside
  6. Pull hook back to correct position with copper wire lined up to pass up through chin and out the top of the nose
  7. Push copper wire up through chin and find the hinge in the upper jaw and pass copper wire through upper jaw at the soft part of the hinge
  8. Wrap copper wire around back under the mono and crimp under the chin of the bait. Pass copper wire through eyes of Ballyhoo and out other side.
  9. Pull wire tight and back around the bottom of the bait
  10. While pulling wire tight take a couple of wide wraps (moving forward) with the wire until it is ¾” in front of the upper jaw’s lip and then make four tight wraps right next to each other. Bend excess wire back toward head of Ballyhoo. Break bill off just in front of the four tight wraps
  11. Put it out and catch a fish!

I will try to get some photos for this page, but I am in China at the moment so unable to do so right now....

 

Get Serious. Get Tormenter!


Dealer and Distributor Inquiries Welcome!

Fax: 561-828-7911
Email: retail@tormenterocean.com

 

Site Powered By
    Small Biz Studio Builder
    Online web site design