Skip to main content
#
 
site map
contact
Shipping Policies
HOME
Board Shorts Main
SPF Performance Shirts
Side To Shorts & Shirts
4X4 Board Shorts
Board Shorts
SURF Board Shorts
Side To Shirts
Men's SPF Performance Shirts
Men's Short Sleeve SPF
Ladies' Board Shorts
Ladies' Printed SPF 50 Tops
Ladies' SPF Shirt/Rash Guards
Ladies Sport T's & Skorts
Youth Apparel
Face Shields
Head Gear
Apparel Catalog
Ladies Board Shorts Measurements
Marlin Camo Performance Shirts
Reef Break Boardshorts
Reef Break II
Shirt, Hat, NUFF Combos
T Shirts
Ladies' Bermuda Collection
Apparel
Offshore Trolling Plastics
Chrome Head Trolling Lures
Daisy Chains & Multi Bait Rigs
Replacement Skirts
Soft Trolling Lures
Looney Birds
Dredge Baits
Ballyhoo Covers
Vertical Jigs, Inshore Jigs, Spoons
Lure Kits & Rigs
Hooks & Rigs
Dredge Witch
Spreader Bars Main
Slap Happy
Replacement Jigging Hooks
Tackle
Surfboards
Surf Leashes
Surf
Rigging a Goggle Eye Harness
Yellowfin Tuna Fishing
Trolling for Grouper
Fishing tips for Wahoo
Live Bait Fishing - Surface
Daytime Swordfishing
Fishing for Dolphin
Making Concrete Weights for Swordfishing
Which Lure Colors?
Trolling without Outriggers
Catching a Spiny Lobster
Jigging for Kingfish
Daisy Chains and How They Work
Which Lure?
Trolling Diagrams
Rigging Ballyhoo
Rigging
About
Salmon Nigiri Plate
Salmon Rice Bowl
Venison Bar-b-que
The Ultimate Nacho
Lemon Mangrove Snapper
Real Bahamian Conch Chowder
Grilled Cajun Spice Dolphin
Italian Seasoned Grilled Yellowfin Tuna
Grilled Florida Lobster Tails
Grilled Kingfish Sandwich
How to prepare a Wahoo Fillet
Fantastic Fish Recipes
Contact
Testimonials

Making Concrete Weights for Daytime Swordfishing

No one sells these, so if you want to go daytime Swordfishing using the "greenest" weights possible, follow these easy instructions:

Start by picking up bags of Quick set concrete mix. This is usually only around $2.50 for 50lb bag which will make up four 12lb weights.

Also needed:

1. Gallon plastic paint "pots" for molds
2. Either Aluminum or Galvanized wire approx 3mm - 4mm in diameter (and strong wire cutters)
3. 5 gallon Bucket
4. Stir stick (approx 1" x 1" and 2.5' long) Square is better than a broom stick as it will scrape the concrete from
    the sides of the bucket much easier
5. Water

Steps:

1. Make up wire loops that are approximately 1" - 2" wide and 6" - 7" long that look like the one in the photo.
    Use a Haywire twist used when making wire leaders. I found that laying the loop in between my fence slats
    was a good way to hold it firm while I twist the ends. Using a vice could also prove handy.

2. Pour around 12lbs of concrete mix into the 5 Gallon Bucket. Add and stir in water per directions on concrete
    bag until you reach proper consistancy. Careful, as most people will tend to add too much water. Stir until all
    concrete is mixed thoroughly.

3. Pour mixed concrete into one of the Paint pots to the desired height. Smooth out the top a bit and then push
    the winged end of your wire loop into the concrete. You will need your stir stick to get all of the mixed concrete
   
out of the bucket.  Place deep enough that it will have a good hold of the newly formed weight. Make sure not to
    allow the wire to reach the bottom of the weight as it will then have the opportunity to leak a rust stain onto
    your deck. Twist it slightly when you get it to the proper depth. Smooth out the top surface again. And repeat
    until you have made all the weights you need.

4. Allow concrete to dry at least 24 hours and then slide them out of the bucket molds. These molds are now re-usable.
    Store your new weights in clean and semi dry area to be ready for your next adventure!

  

Get Serious. Get Tormenter!


Dealer and Distributor Inquiries Welcome!

Fax: 561-828-7911
Email: retail@tormenterocean.com

 

Site Powered By
    Small Biz Studio Builder
    Online web site design